1. DL manuals
  2. Woodstock
  3. Food Prep Table
  4. SHOP FOX W1822
  5. Owner's Manual

Woodstock SHOP FOX W1822 Owner's Manual

Summary of SHOP FOX W1822

  • Page 1

    Owner's manual (for models manufactured since 9/10) model w1822 sliding table attachment phone: (360) 734-3482 • online technical support: tech-support@shopfox.Biz copyright © july, 2010 by woodstock international, inc., revised july, 2011 (ts) warning: no portion of this manual may be reproduced in...

  • Page 2

    This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or...

  • Page 3: Contents

    Se tu p ac ces so ries pa rt s o pe r atio ns sa fe t y in tr o du ct io n use the quick guide page labels to search out information fast! Contents introduction .....................................2 important notice! ................................ 2 woodstock technical support .................. ...

  • Page 4: Introduction

    -2- model w1822 (for machines mfg. Since 9/10) in tr o du ct io n woodstock technical support the model w1822 has been specially designed to provide many years of trouble-free service. Close atten- tion to detail, ruggedly built parts and a rigid quality control program assure safe and reliable oper...

  • Page 5: Safety

    -3- model w1822 (for machines mfg. Since 9/10) sa fe t y safety standard machinery safety safety read manual before operating machine. Failure to follow instructions below will result in personal injury. Standard safety instructions 1. Read through the entire manual before starting machinery. Machin...

  • Page 6

    -4- model w1822 (for machines mfg. Since 9/10) sa fe t y 10. Never leave when machine is running. Turn power off and allow all moving parts to come to a complete stop before leaving machine unattended. 11. Do not use in dangerous environments. Do not use machinery in damp, wet locations, or where an...

  • Page 7

    -5- model w1822 (for machines mfg. Since 9/10) sa fe t y additional safety for sliding table saws read and understand this entire manual and the table saw owner's manual before using this attach- ment. Serious personal injury may occur if safety and operational informa- tion is not understood and fo...

  • Page 8: Unpacking

    -6- model w1822 (for machines mfg. Since 9/10) se tu p the model w1822 has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized shop fox dealer immediately. Unpacking setup inventory refer to figures 1–2 and the l...

  • Page 9: Assembly

    -7- model w1822 (for machines mfg. Since 9/10) se tu p assembly the assembly process typically requires modifications to your table saw. To make the process easier, we strongly recommend that you have another person help you. Also, if you have to drill new holes, we recommend clamping the components...

  • Page 10: Notice

    -8- model w1822 (for machines mfg. Since 9/10) se tu p 3. Thread the foot pad bolts into the bottom of the support legs, as shown in figure 6. For now, do not tighten the jam nuts against the legs so that you can adjust the height of the legs in a later step. Figure 6. Foot pad bolt threaded into th...

  • Page 11

    -9- model w1822 (for machines mfg. Since 9/10) se tu p 7. Align the mounting holes, then thread (2) m8-1.25 x 30 cap screws, 8mm lock washers, and 8mm flat washers through the sliding table into the mounting holes of the saw table. 8. Move the sliding table to the right and install the remaining m8-...

  • Page 12

    -10- model w1822 (for machines mfg. Since 9/10) se tu p figure 12. Locations of the extension table lock levers. Lock levers if the sliding table does not travel exactly parallel to the saw blade, the workpiece could bind and kickback toward the operator, causing serious personal injury. You must ma...

  • Page 13

    -11- model w1822 (for machines mfg. Since 9/10) se tu p 17. Remove the t-bolt from the knurled pivot handle of the crosscut fence and set it aside for use in the next steps. 18. Slide the miter gauge bar into the sliding table miter gauge slot, as shown in figure 13. 19. While holding the crosscut f...

  • Page 14: Operations

    -12- model w1822 (for machines mfg. Since 9/10) o pe r atio ns operations always wear safety glasses when oper- ating this machine. Failure to comply may result in serious personal injury. Do not investigate problems or adjustments while the table saw is running. Wait until the table saw is turned o...

  • Page 15: Crosscut Fence

    -13- model w1822 (for machines mfg. Since 9/10) o pe r atio ns crosscut fence the crosscut fence can be positioned anywhere along the sliding table and at angle between 50° left and 50° right. To position the fence along the sliding table, loosen the two pivot handles, the set screw on the forward e...

  • Page 16: Crosscutting

    -14- model w1822 (for machines mfg. Since 9/10) o pe r atio ns blade crosscut fence workpiece figure 19. Example of large panel rip cutting. Crosscutting the model w1822 enables you to use your table saw to crosscut large panels, as shown in figure 19. To make a crosscut with the sliding table, do t...

  • Page 17: Miter Cutting

    -15- model w1822 (for machines mfg. Since 9/10) o pe r atio ns blade workpiece figure 21. Example of miter cutting with the fence positioned 45° to the left. Miter cutting blade workpiece figure 20. Example of miter cutting with the fence positioned 45° to the right. The crosscut fence can be positi...

  • Page 18: Accessories

    -16- model w1822 (for machines mfg. Since 9/10) o pe r atio ns accessories sliding table saw accessories the following sliding table saw accessories may be available through your local woodstock international inc. Dealer. If you do not have a dealer in your area, these products are also available th...

  • Page 19: Parts

    -17- model w1822 (for machines mfg. Since 9/10) pa rt s 101 103 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 101 102 112 173 115 107 108 101 103 104 170 171 168 172 170 171 172 170 171 172 170 171 172 parts table ref part # description ref part # description 101 xpbhs09m butto...

  • Page 20: Fence

    -18- model w1822 (for machines mfg. Since 9/10) pa rt s fence 121 122 123 124 125 126 128 129 131 132 133 134 135 136 137 138 140 141 142 143 144 145 146 147 148 149 150 151 144 154 155 156v2 157 158 164 165 134 162 139 136 121 172 163 162 169 139 140 144 152 142 130v2 160 159 127v2 163 162 161 161 ...

  • Page 22

    Tape along edges--please do not staple fold along dotted line fold along dotted line woodstock international inc. P.O. Box 2309 bellingham, wa 98227-2309 place stamp here.

  • Page 23: Warranty

    Warranty woodstock international, inc. Warrants all shop fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neglige...

  • Page 24

    High quality machines and tools woodstock international, inc. Carries thousands of products designed to meet the needs of today's woodworkers and metalworkers. Ask your dealer about these fine products:.