Instruction manual model w1667 mini oscillating drill press phone: 1-800-840-8420 • on-line technical support: tech-support@woodstockint.Com copyright © 2000 by woodstock international, inc. Warning: no portion of this manual may be reproduced in any shape or form without the written approval of woo...
Table of contents page 1. Introduction ................................................................................2 about your new drill press ......................................................2 woodstock service and support ................................................2 warranty and ret...
- 2 - introduction about your new drill press this new shop fox ® oscillating drill press has been specially designed by woodstock international, inc. To provide many years of trouble free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and re...
- 3 - shop fox ® machinery warranty woodstock international, inc. Warrants all shop fox ® machinery to be free of defects from workman- ship and materials for a period of 2 years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirec...
- 4 - read manual before operating machine failure to follow instructions below will result in personal injury safety first! 1. Thoroughly read the instruction manual before operating your machine. Learn the applications, limitations and potential hazards of this machine. Keep manual in a safe, conv...
1. Always operate your drill press at speeds that are appropriate for the drill bit size and the mate- rial that you are drilling. 2. Feed the drill bit evenly into the workpiece. Back the bit out of deep holes and clear the chips with a brush after you have turned the machine off. 3. Make sure the ...
-6- this equipment must be grounded. Verify that any existing electrical outlet and circuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a sep- arate 12 a.W.G. Copper grounding wire from the outlet to a known ground. Under no cir- cumstances should the grou...
- 7 - avoiding potential injuries figure 2. Never drill, holding workpiece by hand. Figure 3. Keep fingers away from spinning tool. Fig. 4. Remove switch safety key when not in use. Figure 5. Do not leave handles on when sanding..
-8- figure 6. Components laid out for identification. The following is a description of the components shipped with the w1667 oscillating drill press. It is rec- ommended that the components be laid out in a similar fashion to those in figure 6. This will help in identifying before beginning assembl...
-9- while the main components of the shop fox ® w1667 oscillating drill press are assembled at the factory some assembly is required. The following is the recommended sequence best suited for final assembly. Tools required: you will need a 10mm, 12mm and 14mm open end wrench, a flat tipped screwdriv...
-10- headstock 1. The bottom of the headstock has a pocket for inserting the column. Position the pock- et over the column (figure 10.) and allow the headstock to slide down until it stops (approximately 2"). 2. Align the headstock directly over the foot of the base as viewed from the front of the d...
-11- handles three handles are supplied with your new oscillating drill press. Thread them into the hub as shown in figure 14. Figure 14. Spindle handles installation. Drill chuck figure 13. Inserting the lock screw. Figure 12. Jaws adjusted inside chuck body. The drill chuck is attached to the dril...
-12- speed change adjustments unplug the drill press before changing speeds. The oscillating drill press has 5 speeds ranging from 620 to 3100 rpm. Refer to the speed charts located under the belt guard while following the instructions below. 1. Loosen the belt tension lock. Figure 15. 2. The motor ...
-13- spindle adjustments your new drill press comes fitted with a depth stop for use when drilling. Follow the instruc- tions below for use. 1. Loosen the jam nut on the depth stop rod. Figure 18. 2. Adjust the spindle down while watching the indicator arrow on the scale on the front of the drill pr...
-14- oscillating feature one of the great features of the w1667 drill press is its capability for oscillating sanding. The drill press can be converted from drilling opera- tions to sanding operations in just a few steps. 1. Unplug the drill press and remove the spindle handles. 2. Lift the belt cov...
-15- table adjustments the table can be adjusted to accommodate height of materials to be sanded or drilled. To adjust: 1. Hold onto the table with one hand and loosen the table lock knob. Lift or lower to the desired height. Tighten the table lock knob. Figure 24. 2. The drill press is supplied wit...
-16- operations once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine. Make sure the starting switch is off. The pad- dle is down for off. Make sure all the fasteners and lock handles are tight. Plug in the power cord. Pull the start paddle. M...
-17- to insert a bit, care must be taken to secure the bit firmly in place. When changing bits, proceed as follows: 1. Disconnect the machine from the power source. 2. Open the chuck wide enough to accept a new bit. 3. Install the bit so the chuck jaws will grab as much of the bit shank as it can. F...
-18- maintenance lubrication since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them. For other items on this machine, such as the quill, table and column, an occasional applica- tion of light machine oil is all that i...
-19- the following pages contain general machine data, parts diagrams/lists and warranty/return information for your shop fox ® model w1667 mini drill press. If you need parts or help in assembling your machine, or if you need operational informa- tion, we encourage you to call our service departmen...
- 20 -.
-21- ref part # description 46 x1667046 ball bearing 48 x1667048 retaining ring 49 x1667049 collar 50 x1667050 ball bearing 51 x1667051 collar 52 x1667052 quill 53 x1667053 ball bearing 54 x1667054 spindle shaft 55 x1667055 chuck 56 x1667056 chuck key 57 x1667057 cover spacer 60 x1667060 round belt ...
-22- the speed chart above illustrates the various combinations of pulleys to achieve a desired speed..
Cut along dotted line 10. What stationary woodworking tools do you own? Check all that apply. ___air compressor ___panel saw ___band saw ___planer ___drill press ___power feeder ___drum sander ___radial arm saw ___dust collector ___shaper ___horizontal boring machine ___spindle sander ___jointer ___...
Tape along edges--please do not staple fold along dotted line fold along dotted line woodstock international, inc. P.O. Box 2309 bellingham, wa 98227-2309 place stamp here.