Tannoy CMS 3.0 series Operation Manual - Cms 603Dc Models
9. Technical Specifications
32
CMS 3.0 Series Operation Manual rev 3.0.0
9. Technical Specifications
CMS 603DC Models
Performance
Frequency response (-3 dB)
(1)
BM Backcan
75 Hz - 30 kHz
Frequency range (-10 dB)
(1)
BM Backcan
50 Hz - 30 kHz
Frequency range (-10 dB)
(1)
PI Backcan
46 Hz - 30 kHz
System sensitivity (1 W @ 1 m)
(2)
91 dB (1 W = 4 V for 16 Ohms)
Nominal Coverage Angle
90 degrees conical
Power Handling
(3)
Average
80 W
Programme
160 W
Peak
320 W
Recommended Amplifier Power
160 W @ 16 ohms
Nominal Impedance (Lo, Z)
16 ohms
Rated maximum SPL
Average
110 dB
Peak
116 dB
Transformer Taps (via front rotary switch)
70 V
60 W (83 Ω) / 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) /
OFF & low impedance operation
100 V
60 W (165 Ω) / 30 W (330 Ω) / 15 W (660 Ω) /
OFF & low impedance operation
Transducers
Dual Concentric point source driver
1 x 165 mm (6.5”) Dual Concentric driver, using Omnimagnet technology
Low Frequency
44 mm (1.75”) voice coil, treated multi fiber paper pulp cone
High Frequency
25 mm (1.00”) PEI dome
Physical
Enclosure
Backcan
Zinc plated steel
Baffle
Reflex loaded UL 94V-0 rated ABS
Grille
Steel, with weather resistant coating
Safety Features
Safety ring located at rear of enclosure for load bearing safety bond
Clamping Design
Security toggle clamp
Min / Max clamping range 9.5 mm (0.37”) /
60 mm (2.36”)
Recommended clamp torque: 1.5 Nm
Backcan Options
Blind Mount (BM)
Complete with fixed backcan
Pre Install (PI)
Separate backcan for pre-installation
Cable Entry Options
Cable clamp & squeeze connector for conduit up to 22 mm
Conduit Knockouts on PI Backcan
3 Sets of horizontal positions 19 / 22 / 28 mm (0.75” / 0.87” / 1.10”)
Connectors
Removable locking connector with screw terminals with
“loop through” facility
Compliance
UL-1480, UL-2043, CE
Dimensions
Bezel diameter
274.0 mm (10.79”)
BM Model: Front of ceiling to rear of backcan
255.8 mm (10.07”)
BM Model: Front of ceiling to top of safety loop
273.3 mm (10.76”)
PI Model: Front of ceiling surface to rear of
speaker unit
100.7 mm (3.96”)
PI Model: Front of accessory backcan bezel to
top of safety loop
168.5 mm (6.60”)
Hole cutout diameter (all models)
253 mm (9.96”)
Net Weight (ea)
CMS 603DC BM
6.6 kg (14.56 lbs)
CMS 603DC PI
3.65 kg (8.05 lbs)
PI Backcan
3.68 kg (8.11 lbs)
Included Accessories
C-Ring, tile-bridge kit, paint mask, cut-out template, grille
Optional Accessories
Plaster (mud) ring, Arco grille
Packed Quantity
2
Ordering Information
Part Number
Colour
8001 7440
CMS 603DC BM
White /
Paintable
8001 7450
CMS 603DC PI
White /
Paintable
8001 4181
CMS 603
Zinc Plated
Plaster (Mud) Ring
Steel
8001 7560
CMS 603 PI Backcan
Zinc Plated
Steel
8001 7890
CMS 603 Arco Grille
White /
Paintable
Notes:
1.
Average over stated bandwidth. Measured in
an IEC baffle in an Anechoic Chamber
2.
Unweighted pink noise input, measured at
1 metre on axis
3.
Long term power handling capacity as defined
in EIA - 426B test
A full range of measurements, performance data,
CLF and Ease™ Data for CMS 603DC can be
downloaded from www.tannoypro.com.
Tannoy operates a policy of continuous research
and development. The introduction of new materials
or manufacturing methods may introduce variations
in actual performance; however, actual performance
always will equal or exceed the published
specifications, which Tannoy reserves the right to
alter without prior notice. Please verify the latest
specifications when dealing with critical applications.
Copyright (c) 2014 Tannoy Limited. All rights reserved.
UL-1480,
UL-2043