1. DL manuals
  2. N-Tron
  3. Switch
  4. 100-POE4
  5. User Manual & Installation Manual

N-Tron 100-POE4 User Manual & Installation Manual

Manual is about: Unmanaged Industrial 4-Port Mid-Span POE PSE

Summary of 100-POE4

  • Page 1

    (revised 2011-09-02) 1 100-poe4 unmanaged industrial 4-port mid-span poe pse user manual & installation guide.

  • Page 2

    (revised 2011-09-02) 2 industrial 4-port mid-span poe pse installation guide 100-poe4.

  • Page 3

    (revised 2011-09-02) 3 copyright, © n-tron corp., 2008 820 s. University blvd., suite 4e mobile, al usa 36609 all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a register...

  • Page 4

    (revised 2011-09-02) 4 general safety warnings warning: do not operate the equipment in the presence of flammable gasses or fumes. Operating electrical equipment in such an environment constitutes a definite safety hazard. Warning: if the equipment is used in the manner not specified by n-tron corp....

  • Page 5

    (revised 2011-09-02) 5 hazardous location installation requirements 1. This equipment is suitable for use in class i, div 2, groups a, b, c, and d, or unclassified or non- hazardous locations only. 2. Warning: explosion hazard - substitution of components may impair suitability for class i, division...

  • Page 6

    (revised 2011-09-02) 6 functional overview the 100-poe4 industrial 4-port mid-span poe pse is designed to provide power over ethernet for poe capable devices where running a power line is either not possible or not cost effective. This feature allows an end user to power a poe camera, wireless acces...

  • Page 7

    (revised 2011-09-02) 7 package contents please make sure the package contains the following items: 1. 100-poe4 2. Instruction sheet contact your carrier if any items are damaged. Unpacking remove all the equipment from the packaging, and store the packaging in a safe place. File any damage claims wi...

  • Page 8

    (revised 2011-09-02) 8 din-rail mounting install the unit in a standard din rail. Recess the unit to allow at least 2” of horizontal clearance for cat5e cable bend radius. To install the unit to 35mm industrial din rail, place the top edge of the included mounting bracket on the back of the unit aga...

  • Page 9

    (revised 2011-09-02) 9 front panel from top to bottom: power led v1 poe poe is being applied on the respective port with v1 as a valid source of power. V2 poe is being applied on the respective port with v2 as a valid source of power. Leds: the table below describes the operating modes (port leds ar...

  • Page 10

    (revised 2011-09-02) 10 applying power (top view) unscrew & remove the dc voltage input plug from the top header. Install the dc power cables into the plug (observing polarity on unit). Plug the voltage input plug back into the top header. Tightening torque for the terminal block power plug is 0.22 ...

  • Page 11

    (revised 2011-09-02) 11 n-tron 100-poe4 mid-span poe grounding techniques the grounding philosophy of any control system is an integral part of the design. N-tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immun...

  • Page 12

    (revised 2011-09-02) 12 rj45 connector crimp specifications please reference the illustration below for your cat5 cable specifications:.

  • Page 13

    (revised 2011-09-02) 13 typical application connecting the unit for 10base-t ports, plug a category 3 (or greater) twisted pair cable into the rj45 connector. For 100base-t ports, plug a category 5 (or greater) twisted pair cable into the rj45 connector. Connect the other end to the far end station....

  • Page 14

    (revised 2011-09-02) 14 fcc statement this product complies with part 15 of the fcc-a rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired ope...

  • Page 15

    (revised 2011-09-02) 15 regulatory approvals: safety: ul listed per ansi/isa-12.12.01-2000 (us and canada) and is listed for use in class i, div 2, groups a, b, c, d, t4a emi: en 61000-6-4, en 55011 - class a fcc title 47, part 15, subpart b - class a ices-003 – class a ems: en 61000-6-2 iec 61000-4...

  • Page 16

    (revised 2011-09-02) 16 key specifications physical height: 3.5” (8.89cm) width: 1.489” (3.78cm) depth: 3.53” (8.96cm) weight: 0.7 lbs. (0.31kg) din-rail: 35mm electrical input voltage: 46-49 vdc steady input current: 1.6 a @ 48 vdc (under full load) steady input current: 30 ma @ 48 vdc (under no lo...

  • Page 17

    (revised 2011-09-02) 17 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from n-tron or its authorized reseller....