- DL manuals
- N-Tron
- Switch
- 100-POE-SPL
- User Manual & Installation Manual
N-Tron 100-POE-SPL User Manual & Installation Manual
Summary of 100-POE-SPL
Page 1
(revised 2010-11-15) 1 100-poe-spl industrial power extractor user manual & installation guide.
Page 2
(revised 2010-11-15) 2 industrial poe power extractor installation guide 100-poe-spl-xx unmanaged industrial poe power extractor where "xx" is: 12 for 12vdc output voltage option 24 for 24vdc output voltage option 48 for 48vdc output voltage option xx custom output voltages.
Page 3
(revised 2010-11-15) 3 copyright, © n-tron corp., 2008 820 s. University blvd., suite 4e mobile, al usa 36609 all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a register...
Page 4
(revised 2010-11-15) 4 electrical safety warnings this equipment is suitable for use in class i, division 2, groups a, b, c, and d or non-hazardous locations only. Warning – explosion hazard – substitution of components may impair suitability for class i, division 2. Warning – explosion hazard – do ...
Page 5
(revised 2010-11-15) 5 environmental safety warnings warning: disconnect the power and allow to cool 5 minutes before touching. 100-poe-spl-xx industrial power extractor the 100-poe-spl-xx is a poe splitter designed to accept ethernet with poe via cat5e cable and output power via terminal block and ...
Page 6
(revised 2010-11-15) 6 package contents please make sure the package contains the following items: 1. 100-poe-spl-xx poe power extractor 2. Product cd contact your carrier if any items are damaged. Unpacking remove all the equipment from the packaging, and store the packaging in a safe place. File a...
Page 7: Urmk
(revised 2010-11-15) 7 din-rail mounting install the unit in a standard din rail. Recess the unit to allow at least 2” of horizontal clearance for cat5e cable bend radius. To install the unit to 35mm industrial din rail, place the top edge of the included mounting bracket on the back of the unit aga...
Page 8
(revised 2010-11-15) 8 front panel from top to bottom: green terminal block voltage output 12/24/48vdc connector (model dependent) green led lights when power is present poe in rj45 connector for data and poe in data out rj45 connector for data only out leds: the table below describes the operating ...
Page 9
(revised 2010-11-15) 9 applying power (top view) unscrew & remove the dc voltage output plug from the top header. Install the dc power cables of the device to be powered into the plug (observing polarity on unit). Plug the voltage output plug back into the top header. Tightening torque for the termi...
Page 10
(revised 2010-11-15) 10 n-tron switch grounding techniques for the 100-poe-spl-xx the grounding philosophy of any control system is an integral part of the design. N-tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noi...
Page 11
(revised 2010-11-15) 11 connecting the unit for 10base-t ports, plug a category 3 (or greater) twisted pair cable into the rj45 connector. For 100base-tx ports, plug a category 5e (or greater) twisted pair cable into the rj45 connector. Connect one cable from the poe power sourcing equipment into th...
Page 12
(revised 2010-11-15) 12 fcc statement this product complies with part 15 of the fcc rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ...
Page 13
(revised 2010-11-15) 13 100-poe-spl-xx - key specifications physical height: 4.30” (10.92 cm) width: 1.00” (2.54 cm) depth w/ typical sfp installed: 3.91” (9.94 cm) including din-rail mount: 4.15” (10.55 cm) weight: 0.60 lbs (0.27 kg) din rail: 35 mm electrical input voltage: poe 48vdc (ieee 802.3af...
Page 14
(revised 2010-11-15) 14 regulatory approvals: safety: ul listed per ul 508 and isa-12.12.01-2007 (us and canada) for use in class i, div 2, groups a, b, c, d, hazardous or non-hazardous locations; temperature code of t4. Emi: en61000-6-4, en55022 - class a fcc title 47, part 15, subpart b - class a ...
Page 15
(revised 2010-11-15) 15 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from n-tron or its authorized reseller....