Summary of SCG 50H
Page 1
Www.Wholesalegateopener.Com.
Page 2: Table of Contents
1 table of contents general safety ……………………………………..……………………………………......………………….. 2 preparation for installation ……………………………………………..…………………………………......…….. 3 parts list ………………………………………..….…………………………………......…………………………. 4 optional accessories part list ………………………………………..….…………………………………......… 5 technic...
Page 3: General Safety
2 thank you for purchasing scg-50h sliding gate opener. We are sure that the products will be greatly satisfying as soon as you start to use it. The product is supplied with a user’s manual which encloses installation and safety precautions. These should be read carefully before installation and ope...
Page 4: Preparation For Installation
3 • do not allow persons or children to remain in the automation operation area. • keep radio control or other control devices out of children’s reach, in order to avoid unintentional automation activation. • the user must avoid any attempt to carry out work or repair on the automation system, and a...
Page 5: Parts List
4 parts list.
Page 6
5 optional accessories parts list technical specifications & features specifications ·power supply: 120v/60hz or 230v/50hz ·motor: 120vac or 230vac ·absorbed power: 750w ·gate moving speed: (7.9“/second) 20 cm/second ·max gate weight: 2,600kgs ·max torque: 75nm ·environmental conditions: from -15°c ...
Page 7: Installation Overview
6 ·get the desired chain tension by adjusting the chain bolts. ·reliable rolling code technology ·emergency release key in case of power failure ·stop/reverse in case of obstruction during gate opening/closing ·built in adjustable auto-close (0, 30, 60, 90 seconds) ·built in max. 90 seconds motor ru...
Page 8: Manual Operation
7 the installation proceeds are as follows: 1.Dig a hole for a concrete pad which should be approximately 60 x 36 x 35cm (24〞x 14〞x 14〞). It may protrude 10 cm (4”) above ground and 25 cm (10”) in depth underground. Increase the pad height if necessary to protect the system from flooding, heavy snow...
Page 9
8 installation of chain and chain brackets 1. Chain brackets 1). Please refer to below chain brackets figure, which shows “u” bolt, “l” bracket and chain bolt. Use the “u” bolts (square or round) to attach the chain brackets to gate frame. 2). If both the square bolts and round bolts are not fit for...
Page 10
9 2). The opener must be parallel to the gate. 3). Make sure there is 1” distance at least between the chain box and the gate after you position the base plate. Installation of magnets for limit switches before install limit switch, make sure the gate opener is put in manual operation. (the clutch c...
Page 11
10 connecting of the control board.
Page 12: Setting of The Control Board
11 1. Motor the black wire of the motor should be connected into the “6” terminal. The red wire of the motor should be connected into the “7” terminal. The yellow wire of the motor should be connected into the “8” terminal. 2. Start capacitor one pin of the start capacitor should be wired to the “7”...
Page 13
12 this mode enables user to drive the vehicle through the gate quickly when the gate opens to certain width. Dip switch #1: on – 2 seconds off – 0 dip switch #2: on – 4 seconds off – 0 note: the midway function would be disabled if both dip switches are turned off. Factory default setting is disabl...
Page 14: Troubleshooting
13 test the reversing sensitivity for the sake of safety, it is very important to test the reversing sensitivity as soon as the control board set is finished. The reversing sensitivity adjustment is inverse correlation with stall force adjustment in potentiometer a and potentiometer b. In other word...
Page 15: Maintenance
14 b. The limit switches are failed. Disconnect the limit switches and try it again. C. Connecting wires or terminal blocks are too loose. Check the connecting wires and terminal blocks. D. The motor has been damaged. Replace the motor if necessary. E. The thermal protector is working because the hi...
Page 16
Www.Wholesalegateopener.Com 7106 s 220th st, kent wa 98032 usa sales@wholesalegateopener.Com ©2010-2012 lockmaster all rights reserved.