Summary of L110C
Page 1
Sliding gate operator user's manual model: l110c www.Openers4less.Com.
Page 2
L110c/l110 sliding gate operator 2 outline 1. Important safety information …………………3 2. Main functions …………………………………3 3. Technical parameters …………………………3 4. Packing list ……………………………………3 5. Installation ……………………………………5 6. Connect the wires ……………………………9 7. Adjustment ……………………………………9 8. Maintenance …………...
Page 3
L110c/l110 sliding gate operator 3 1. Important safety information carefully read and follow all safety precaution and warnings before attempting to install and use this operator, incorrect installation can lead to severe injury. The gate operator should be installed by a qualified technician; other...
Page 4: Tools You Will Need
Residential sliding gate operator tools you will need during assembly and installation of your opener, the instructions will call for the use of various tools shown below. Other tools may be required as needed for the installation of the concrete pad and electrical connection. Table 3 required tools...
Page 5
L110c/l110 sliding gate operator 4 fig.1 l110c accessories l110 gate operator packing list no. Item quantity 1 gate operator 1 2 release key 2 3 operator base (spare accessory) 1 4 tighten bar 2 5 block bracket 2 6 sprocket cover 1 7 screw for mounting driven sprocket bracket (m8x16) 4 8 anchor bolt...
Page 6
L110c/l110 sliding gate operator 5 fig.2 l110 accessories 5. Installation the l110c/l110 chain-driven gate operator operates by forcing a straight piece of chain. This length of chain is extended between two chain brackets located at opposite ends of the gate. The entire configuration is shown in th...
Page 7
L110c/l110 sliding gate operator 6 fig.4 l110 conduit in order to protect the wires, conduit must be preset into the concrete when it is poured. Wires within the conduit shall be located or protected so that no damage can result from contact with any rough or sharp part. Concrete pad the base unit o...
Page 8
L110c/l110 sliding gate operator 7 driven sprocket bracket fix the driven sprocket bracket on both sides of the operator. Operator in locations where ground freeze is possible, mount the gate operator as shown in fig.5 installation 1 or installation 2. Check the operator and make sure it is lined up...
Page 9
L110c/l110 sliding gate operator 8 drive sprocket driven sprocket driven sprocket fig.9 sprocket cover mount the sprocket cover with screws. Limit switch l110c-magnets for limit switch (see fig.10) install the magnet as shown in fig.10 below. The magnet and limit switch are used to control the posit...
Page 10
L110c/l110 sliding gate operator 9 l110-spring limit switch (see fig.11) to ensure safety, it is recommended to install limit devices at both ends of the gate to prevent the gate from sliding out of the rails. The rails must be installed horizontally. The spring limit switch and blocks are used to c...
Page 11
L110c/l110 sliding gate operator 10 tighten (or release) the force adjust bolt on the motor top to increase (or decrease) the output torque (i.E. Output force of the operator), and ensure the gate safely. Adjust the output torque in the safety range before using the operator. 8. Maintenance ensure t...
Page 12: Step #2
Step #2 install the control board onto the motor by mounting it on the small white clips that are on the large mounting plate. (as shown below) step #3 install the receiver onto the motor by mounting it on the small white clips that are on the small mounting plate. (as shown below) step #1 unscrew t...
Page 13: Step #4
Step #4 now you will begin the installation by screwing the wires that are coming from the small receiver board onto the terminals (see pic 1, right) from the control board, in the following order: terminal 10 - green wire terminal 11 - red wire terminal 12 - yellow wire (any) terminal 13 - yellow &...
Page 14: Step #6
Step #6 find the plug with the blue & yellow wires on it. Connect the plug on to the control board on the section labeled: "capacitor" (as shown on the pic, right) step #7 find the plug with the red, white & blue wires on it. Connect the plug on to the control board on the section labeled: "limit sw...
Page 15
Ac slide gate controller feature selector auto close feature limit switch type on: normally close off: normally open when using auto close features l di it h h ld b dip 1 10 auto close feature 12.5 seconds 25 seconds 45 seconds only one dip switch should be on. The other two dip switch should be in ...
Page 16: Receiver
Transmitter/remote control (shown in figure 9) 1. Yellow button channel 2. Blue button channel 3. Indicator light 4. Yellow button channel – exposed 5. Dip switch 6. Battery 7. Blue button channel – exposed 8. Back side cover figure 9 receiver 1. Channel 1 dip switch (yellow button on remote control...
Page 17
Residential sliding gate operator 13 optional equipment installation procedures o o o o o o o o o o o o blue brown black white grey grey black black green brown red black.
Page 18
©2005-2009 lockmaster all rights reserved sales@openers4less.Com www.Openers4less.Com.