Festool TDK 12 Operating Instructions Manual - page 7
10
b)
Fitting/removal of chuck on angle
attachment
The chuck is fitted on the shaft (2.6) of the
angle attachment in the same way as on the
drill spindle of the machine.
3.3
Eccentric attachment DD-ES
The eccentric attachment is used to hold bits.
It allows screwing close to edges.
a)
Fitting/removing the eccentric
attachment
The eccentric attachment is fitted/removed in
the same was as the angle attachment (see
Chapter 3.2).
b)
Changing tools
- Pull the unlocking ring (2.8) back and remove
the tool and/or insert the new tool.
3.4
CENTROTEC WH-CE toolholder
The CENTROTEC toolholder enables rapid
changes of tools with CENTROTEC shafts.
Do not fit CENTROTEC tools at the
round shaft section in a conventional
chuck to prevent damage to the shaft.
Danger of injury! When changing
tools, handle the tool and its sharp
cutters with special care and wear
protective gloves, if necessary.
a)
Fitting/removing CENTROTEC
Fitting
- Pull the release ring (2.11) forwards, place
the toolholder as far as it will go on the drill
spindle (2.5) and let go of the release ring.
Removal
- Pull the release ring forwards and take off
the toolholder.
b)
Changing tools
- To insert or remove a tool with CENTROTEC
shaft, pull the green release ring (2.10) back.
On inserting the tool, turn it until its hex shank
arbour (2.9) locks in place in the hexagonal
shank of the drill spindle, and push the tool
into the toolholder as far as it will go.
3.5
Tool holding fixture in the drill
spindle
Bits can be fitted directly in the hexagon socket
holder of the drill spindle (2.5) to make the
machine lighter and shorter.
4
Charge battery pack
To load the battery pack, push it into the hol-
der (3.1) on the charger up to the stop. Per-
form this in reverse to remove the battery pack
from the charger.
The battery type used (NiCd or NiMH) is
detected automatically.
Charging is controlled by a microprocessor.
If a warm NiMH battery pack (>37° C) is
inserted, charging will only be carried out at a
lower charge current. In this case, the charging
time is extended.
The LED (3.2) indicates the respective
charging state of the charger.
LED yellow steady:
Charger is ready for use.
LED green flashing:
Battery pack being charged.
LED green steady:
Battery pack fully charged, conservation
charge on.
LED red flashing:
General malfunction, e. g. full contact not
being made, short-circuit, battery pack faulty.
LED red steady:
Temperature of battery pack is outside
permissible limit.
It is essential that you read the
instructions in the Chapter
Working
instructions
-
Maintenance - Care.
5
Working with the machine
5.1
Initial operation
Turn on by pressing button (1.3). Depending
on the pressure exerted on the button, the
adjustment of running speed can be varied
infinitely.
Turn off by releasing the button (1.3).
After releasing the button, the chuck is stopped
and therefore, after-running of the equipment
is prevented.
5.2
Bit storage well
You can insert several bits or bit extensions
into the bit magazine (1.2) from the side.
The magnetic attachment allows you to pick
up screws and similar objects.
6
lnstructions on application -
maintenance - care
Please pay attention to the
following instructions. Otherwise
there is a risk of damage to the tool,
charger or battery pack.
- Repairs may only be performed by authorised
technicians. LC 45 charging device: Even after
disconnection from the mains, there is still a
high capacitor voltage on the power output
component on the inside of the device.
- Keep the air vents of the electronic equipment
and the charger clean to guarantee the air
circulation for cooling.
- No metal objects (metal chips) should enter
the charger at the contact points as well as
through the cooling slits into the equipment
(danger of short circuit).
- Only use original Festool battery packs.
Seen at Ideal Tools.