- DL manuals
- Fervi
- Sander
- 419
- Original Instructions Manual
Fervi 419 Original Instructions Manual
Summary of 419
Page 1
Operation and maintenance manual 150 mm air orbit sander art. 0419 original instructions fervi.Com.
Page 2: Foreword
Hardware page 2 of 13 foreword read this manual before operating any machinery original instructions before starting any operation it is compulsory to read this instruction manual. The guarantee that the machine will function and perform properly is strictly dependent upon the application of all the...
Page 3: Contents
Hardware page 3 of 13 contents 1 general safety instructions............................................................. 4 1.1 risks associated with the work area ............................................................................4 1.2 risks associated with the presence of rotating and/or ...
Page 4: Parts
Hardware page 4 of 13 1 general safety instructions 1. During use, maintain control of the tool. The operators represent the most important aspect of safety. To best protect against the risk of injury, work cautiously and carefully. 2. The pneumatic tool should not be used and repaired by someone un...
Page 5: 1.4 Technical Support
Hardware page 5 of 13 1.3 personal protective equipment when using the pneumatic tool, always wear the following: safety shoes work gloves hearing protection (cap, earplugs, etc.) protective goggles 1.4 technical support for any problems and/or concerns, please contact, without hesitation, the custo...
Page 6: Use
Hardware page 6 of 13 2 description of the sander and intended use the sander is a portable pneumatic tool, to be used for the finishing large surfaces. By changing the abrasive tools (discs), it is possible to smooth or polish different materials, such as metals, wood and plastic. The sander art. 0...
Page 7
Hardware page 7 of 13 3 improper use and contraindications it is strictly forbidden to !! allow the tool to be used by untrained personnel and those who have not read the instruction manual; use the tool for different purposes and uses other than those for which it was designed, i.E. Smoothing a...
Page 8: 4 Commissioning
Hardware page 8 of 13 4 commissioning 1. Remove the air inlet cap, then screw the nozzle into hole: 1/4" npt male quick-release coupling 2. Put a few drops of lubricating oil (without resin acid) in the air inlet nozzle. 3. Check the flexible air supply hose. If it is damaged, broken, torn or deform...
Page 9: 5 How To Use
Hardware page 9 of 13 5 how to use 5.1 attaching the abrasive tools (discs) crushing and cutting before attaching and/or removing the discs, always remove the air supply hose. Protective gloves before attaching and/or removing the discs, wear suitable protective gloves. 1. Select the disc with the d...
Page 10: Emergency
Hardware page 10 of 13 the sander is equipped with a knob for adjusting the rotation speed of the disc according to the type of material and the type of work to be performed: the harder the material, the greater the speed of rotation. Turn the speed adjustment lever of the disc to the desired positi...
Page 11
Hardware page 11 of 13 6 maintenance and cleaning the purpose of this chapter is to provide all the information on maintenance procedures and their frequency as required by the sander. Intervention frequency daily weekly 1. General visual inspection x 2. General cleaning x 3. Clean the air outlet no...
Page 12
Hardware page 12 of 13 7 bill of materials and spare parts fervi.Com.
Page 13
Hardware page 13 of 13 ref. Description ref. Description 0419/01 main body 0419/23 o-ring 0419/02 upper part 0419/24 pin 0419/03 start lever 0419/25 rotor 0419/04 pin 0419/26 rotor blade 0419/05 seeger 0419/27 rear cylinder head 0419/06 o-ring 0419/28 bearing 0419/07 pin 0419/29 seeger 0419/08 o-rin...