Eagle AVI Installation & Owner's Manual - Input P
12
AVI Slide Rev - C
Input P
o
wer Connection
Limit Switc
hes & Open Left/Right
MOTOR 15A
OPENING
TIMER
ERD CONTROL
MULTI FUNCTION
GATE STATUS
FEATURE SELECTOR
M/S PHASE
1
0
CLOSING
MASTER
OPEN RIGHT
BRAKE ON
CLOSE TIMER ON
SLAVE
OPEN LEFT
BRAKE OFF
CLOSE TIMER OFF
1
ON
2
3
4
OFF—ON
SELECT
MIN
MAX
OPEN
LIMIT
ERD OVERLOAD
OPENING CLOSING CLOSED
LIMIT
SLAVE MASTER
+ –
+ –
#9
#8
+ MAGLOCK
- 24 VDC
#5
+ ALARM
- 12 VDC
#6
REVERSE
LOOP
#2
POWER
24V
AC
#7
KEY
#3
M-FCN
#4
GND
GND
RCVR
24VAC
#1
COMM PORT
INPUT/OUTPUT
RECEIVER
ERD
M/P
RESET
1
O
N
2
ON ON STOP N/C
ON OFF CLOSE
OFF ON PHANTOM
OFF OFF EDGE SENSOR
S1 S2 FCN
COMM PORT
POWER
120 VAC Input Power Connection
Setting the: Limit Switches & Open Left or Open Right
WARNING:
Eagle Access Control Systems, Inc. is not responsible for
researching and complying with local building codes. Be sure to check
all local building codes before installation.
Be sure that the circuit breaker for the input power is turned OFF
before connecting the input power to the operator.
All operators MUST be properly grounded.
Installing surge protection is recommended.
The limit nuts MUST be set so the
gate stops at the correct open and close
positions. the control board MUST have power
for the limit LEDs when setting the limit nuts.
Adjust the close limit nut FIRST when the gate
is in the closed position.
Removing Release Knob will
allow control board plate to be
rotated up and gain easier
access to limit box, see above.
IMPORTANT: DO NOT
cycle the operator before
setting the limit nuts. Damage or injury could occur
if limit nuts are NOT set correctly. (See below)
Limit
Nut LED
Limit
Nut LED
OPEN LEFT
OPEN RIGHT
Wire Color Description
Black - 120 VAC input power
White - Neutral input
Green - Ground input
(from an approved grounding method)
CAUTION
CAUTION
Be sure that power is turned OFF.
To Set the Limit Nuts:
GATE STATUS
OPEN
LIMIT
OPENING CLOSING CLOSE
LIMIT
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
CLOSE
CLOSE
CLOSE
CLOSE
CLOSE
CLOSE
CLOSE
CLOS
LOS
Indicates the direction
the gate is cycling.
250 ft
14 AWG
400 ft
12 AWG
650 ft
10 AWG
1000 ft
8 AWG
2000 ft
125 ft
200 ft
325 ft
500 ft
1000 ft
4 AWG
Single Operator
Dual Operators
Black wire to Black wire.
White wire to White wire.
Green wire to Green wire.
120 VAC
FEATURE SELECTOR
MASTER
OPEN RIGHT
BRAKE ON
CLOSE TIMER ON
SLAVE
OPEN LEFT
BRAKE OFF
CLOSE TIMER OFF
1
ON
2
3
4
OFF—ON
SELECT
With power turned ON, press and
hold spring loaded locking tab
and rotate limit nuts accordingly
until LEDs light. Make sure nuts
are locked in position after
releasing locking tab.
120 VAC Input Power Wire
Locking T
ab
Limit
Switch
Limit
Switch
Limit Nut
Limit Nut
Release Knob
Control
Board
Plate
Limit Box
Control
Board
Plate
Release
Knob